, ,

FEYNLAB INDUSTRIAL

INCLUDED

FEYNLAB® INDUSTRIAL COATING – 275ml or 1L

Can be applied by spraygun or by hand using the FEYNLAB White Microfiber Foam Applicator Pads.
( contact us for further instructions on both methods )

 

COVERAGE RATES

The coverage rates vary depending on application and porosity of the surface. However, expect approximately 400 sq. ft. per Liter or 100 sq. ft. per 275ml bottle.

 

CAUTIONS

Always be sure to use all PPE equipment during use of FEYNLAB® INDUSTRIAL. This includes nitrile gloves, safety glasses, and an approved n95/p100 respirator. Make sure the application area is well ventilated to allow fumes to dissipate quickly. Avoid all skin contact. Do not ingest. Keep out of reach of children. In case of accidental skin or eye contact, rinse immediately and thoroughly with water.

Test in an inconspicuous area of any surface prior to treating a large area.

DO NOT apply indoors or in areas that are not well ventilated.


SURFACE PREPARATION

  • Painted Surfaces or Colored Plastics – Wash thoroughly with FEYNLAB® PURE WASH followed by a wipe-down with a degreaser such as Acetone. Allow surface to dry completely.
  • Stone, Wood, Bare Metal, Concrete – Wash thoroughly with FEYNLAB® PURE WASH. Allow surface to dry completely.


Shelf Life

Unopened: 1 Year

Opened: 3-4 months – With proper storage: in a temperature controlled environment 10°C-24°C (50°F-75°F) and out of sunlight. ALWAYS keep cap on bottle when not in use.


APPLICATION INSTRUCTIONS (INDUSTRIAL USE)

  1. Ensure the application area is prepped and completely dry.
  2. Shake FEYNLAB® INDUSTRIAL for 10 seconds.
  3. Open the container slowly. Use a towel covering the lid as you slowly open. Shaking creates pressure which may cause contents to pressurize and possibly spill out if opened carelessly.
  4. Carefully pour product into a separate application bottle (not provided) and fasten lid back on the original FEYNLAB® INDUSTRIAL bottle tightly. Using a separate bottle for application avoids contamination of the original FEYNLAB® INDUSTRIAL product. With this method any dirt or debris contacting applicator pads cannot contaminate the INDUSTRIAL source container.
  5. Apply several drops to the FEYNLAB® WHITE INDUSTRIAL APPLICATOR PAD for the best possible leveling. Other applicators will work but may leave unsightly application lines.
  6. Apply the coating with only straight lines and long strokes, moving East to West. Overlap passes by 50% with a maximum of only two passes over any given area. This method allows the coating to flow out as level as possible, while keeping the applicator pad wet during application.
  7. Continue this overlapping application process until all desired areas are fully covered.
  8. Allow FEYNLAB® INDUSTRIAL to cure for 24 hours before exposing to any water or liquids. If possible, expose to direct sunlight to accelerate the curing process.

 

**NOTE: TO ACHIEVE PERFECT SURFACE CLARITY A THINNER FILM BUILD APPLICATION MAY BE NECESSARY. IF THIS IS THE DESIRED OUTCOME, PLEASE FOLLOW THE SECOND SET OF INSTRUCTIONS BELOW.

 

APPLICATION INSTRUCTIONS (OPTIMAL SURFACE CLARITY)

  1. Ensure the application area is prepped and completely dry.
  2. Shake FEYNLAB® INDUSTRIAL for 10 seconds.
  3. Open the container slowly. Use a towel covering the lid as you slowly open. Shaking creates pressure which may cause contents to pressurize and possibly spill out if opened carelessly.
  4. Carefully pour product into a separate application bottle (not provided) and fasten lid back on the original FEYNLAB® INDUSTRIAL bottle tightly. Using a separate bottle for application avoids contamination of the original FEYNLAB® INDUSTRIAL product. With this method any dirt or debris contacting applicator pads cannot contaminate the INDUSTRIAL source container.
  5. Apply several drops to the FEYNLAB® WHITE INDUSTRIAL APPLICATOR PAD for the best possible leveling. Other applicators will work but may leave unsightly application lines.
  6. Apply the coating with long straight lines, overlapping 50%. After East to West passes, crosshatch the section (switch to North to South lines) 3-4 times to spread the coating thinner across the surface.
  7. Continue this process until you have covered a 4ft by 4ft section.
  8. Once a 4ft by 4ft section is covered with INDUSTRIAL, prepare a new white microfiber applicator with FEYNLAB® LEVELING AID. With little to no pressure, gently glide the LEVELING AID applicator over the surface using the same crosshatch pattern until the underlying INDUSTRIAL COATING feels smooth. Do not use unnecessary pressure.
  9. After the LEVELING AID applicator glides smoothly over the entire surface, begin wiping the surface clear with a microfiber towel. A smaller towel will help with any bunching issues that might occur.
  10. Follow with a second clean microfiber towel to ensure the 4ft by 4ft area is perfectly clear. If any areas appear to have residue or do not look optically clear, then immediately repeat steps 7-9.
  11. Allow FEYNLAB® INDUSTRIAL to cure for 24 hours before exposing to any water or liquids. If possible, expose to direct sunlight to accelerate the curing process.

FEYNLAB® INDUSTRIAL COATING is a high-solids, single-component coating with excellent chemical, abrasion, and UV resistance. FEYNLAB engineered this coating specifically for applications where long-life aesthetics are required, even in the harshest environments. Intended for exterior use only.

FEYNLAB® INDUSTRIAL COATING can be applied by hand using the specific white Industrial applicator pad & if necessary using Feynlab Original or Feynlab Levelling Aid to acheive a smooth finish.
Alternatively FEYNLAB® INDUSTRIAL COATING can be applied using a spray gun.  Contact us for suggested spray equipment and preparation chemicals and methods see  https://www.facebook.com/groups/1079577089722878

FEYNLAB® INDUSTRIAL COATING – Benefits

FEYNLAB® INDUSTRIAL COATING is an innovative multi-purpose UV-resistant formula designed for exceptional protection across various hard surfaces, including metal, concrete, plastic, and more. As a high-solids single-component coating, it provides superior resistance to chemicals, abrasion, and sun exposure, making it the ideal solution for harsh outdoor environments. Whether utilized for industrial equipment, commercial buildings, and structures, or residential aesthetic upgrades, this durable coating retains aesthetics and prevents degradation caused by continuous UV ray damage.

FEYNLAB® leverages cutting-edge engineering to create a resilient, long-lasting finish that maintains peak quality and appearance, despite exposure to extreme environmental factors over time. With simple spray application, impressive adhesion, and reliable high-performance versatility, professionals can rely on INDUSTRIAL COATING for a wide variety of client coating projects.

Intended for EXTERIOR USE ONLY.

APPROVED SURFACES FOR APPLICATION – DO NOT apply to unapproved surfaces:

  • Painted Metal & Other Painted Surfaces
  • Colored plastics
  • Stone
  • Wood
  • Concrete

 

Reviews

There are no reviews yet.

Be the first to review “FEYNLAB INDUSTRIAL”

Your email address will not be published. Required fields are marked *